CLOSE
Home Training Services In-House Training

In-House Training

In-house Training is intended to bestow our clients with boundless insight at the best cost. Arranging an improved course material and training solution that fits your requirements and fulfill the training needs for your employees.

Benefits:

  • Specific Course Material
    Course material customization to comply with your needs given by our expert trainers.
  • Cost Efficient
    Adjustable financial budget to the specific course material desirable.
  • Convenient
    Liberty to decide the training venue and schedule to fit with your condition.
  • Precise Solution
    Accurate practical hints and tips for immediate practice in the field given by our trainers.
  • Confidentiality
    Closed training environment to ensure the information and conversation confidentiality of between you and our trainers.

SEND US YOUR INQUIRY

Name:

Company:

Job Title:

Email:

Phone No.:

Subject:

Message:


Find Our Available Course

  1. Advanced Distributed Control System (DCS)
  2. Advanced Flow Measurement
  3. ANSI/ASME 31.4 & 31.8 Offshore Pipeline
  4. ANSI/ASME 31.4 & 31.8 Onshore Pipeline
  5. Audit Energi, Carbon Accounting, Konversi Lingkungan
  6. B31.3 Process Piping Code Design Requirements
  7. Basic Fire & Explosion Science Behavior
  8. Basic Non Destructive Testing (NDT)
  9. Basic Welding
  10. Basic Welding Technology (Overview)
  11. Bearing & It’s Failure
  12. Boiler Operation & Maintenance
  13. Calibration ISO / IEC 17025
  14. Centrifugal Compressor: Selection, Operation, Maintenance
  15. Centrifugal Pump: Selection, Operation, Maintenance
  16. Choke and Control Valves
  17. Circulating Fluidized Bed Boiler and Turbine
  18. Compressor: Operation, Maintenance & Troubleshooting
  19. Compressor: Selection, Operation, Maintenance
  20. Corrosion & It’s Prevention
  21. Corrosion Control Management
  22. Cost Management
  23. Culture Change for Maintenance & Reliability Improvement
  24. Dasar Pemetaan
  25. Diesel Engine: Operation & Maintenance
  26. Distributed Control System (DCS) Fundamental
  27. Effective Maintenance Management
  28. Electrical & Control Troubleshooting Simulation
  29. Electrical Control Wiring
  30. Electrical Safety
  31. Emergency and Shutdown Systems
  32. Failure Analysis for Industrial Equipment
  33. Failure Mode & Effect Analysis (FMEA)
  34. Fire & Explosion Investigation Forensic Engineering
  35. Fire & Explosion Risk Assessment
  36. Fitness for Service
  37. Flow Assurance in Piping System
  38. Flow Measurement
  39. FRP Technology for Oil & Gas Industry
  40. Gas Chromatography
  41. Gas Engine Principle and Practices
  42. Gas Metal Arc Welding (Las MIG/MAG)
  43. Gas Metering, Instrumentation and Calibration
  44. Gas Pipeline Hydraulic
  45. Gas Tungsten Arc Welding (Las TIG)
  46. Gas Turbine: Operation & Maintenance
  47. Hazardous Materials and Hazardous Waste Handling
  48. HAZOP
  49. Health Risk Assessment
  50. Hydraulic Analysis
  51. Industrial Combustion And Burner Operation And Optimization For Natural Gas Fuel
  52. Inspeksi Pengelasan untuk Non Welding Inspector
  53. Inspeksi Teknis Migas (Technical Oil and Gas Inspection)
  54. Instrumentation, Electronics and Control
  55. Integrated Maintenance Strategy
  1. Interpretation of P&ID and PFD
  2. Introduction to Metallurgy & Corrosion
  3. Life Cycle Costing
  4. Lifetime Assessment & Extension Program
  5. Maintenance Cost Engineering – Asset Management
  6. Maintenance, Diagnostic, Inspection & Troubleshooting Relay Protection
  7. Maintenance Planning & Scheduling
  8. Manual Metal Arc Welding (Las Listrik)
  9. Mechanical Design & Engineering
  10. Metallic Material Selection
  11. Metallurgy for Non Metallurgist
  12. Metering System: Design, Specification, Installation and Maintenance
  13. Modern Maintenance Management
  14. NDT for User
  15. Non-Metallic Material
  16. Oxy-Acetylene Welding (Las Asetilin)
  17. Pemetaan Spasial
  18. Penyusunan Dokumen Lingkungan & Konsekuesinya
  19. Petroleum Industrial Refrigeration: Operation and Maintenance
  20. Pipe Stress Analysis using Caesar II Software
  21. Pipeline Engineering
  22. Pipeline Integrity
  23. Pipeline Integrity Management System (PIMS)
  24. Piping & Pipeline System: Fabrication, Design, Specification, Installation & Maintenance
  25. PLC and Automation
  26. Predictive & Preventive Maintenance
  27. Production Safety System
  28. Project Management
  29. Project Planning & Control
  30. Pump: Selection, Operation, Maintenance
  31. QC Mechanical
  32. Reliability Centered Maintenance (RCM)
  33. Risk Based Inspection (RBI)
  34. Root Cause Failure Analysis in Oil & Gas Company
  35. Rotating Equipment: Operation & Maintenance
  36. Safety Instrumented System & Control
  37. Safety Instrumented Systems (SIS): ISA, IEC
  38. Safety Protection of Gas Turbine Generator System
  39. SCADA System & GSM
  40. Sertifikasi NDT Level 1: Magnetic Particle Testing (MP), Liquid Penetrant Testing (PT)
  41. Sertifikasi SKPP & SKPI Migas
  42. Sistem Hidrolik dan Pneumatik
  43. Standar Konstruksi
  44. Storage Tank Technology: Design, Operation, Maintenance & Inspection
  45. Strategy Moves
  46. Survey, Pemetaan and GIS
  47. Total Productive Maintenance (TPM)
  48. Turbin Air
  49. Valve Technology
  50. Vibration Analysis
  51. Welding Inspection
  52. Welding Technology
  53. Wellhead Instrumentation and Hydraulic Control System